Material Testing Industry Standards
DDL is experienced in performing tests that comply with the following material testing industry standards:
|
|
| ID 26 | Infusion Pump Performance Testing |
| ASTM Standards | |
| A370 | Mechanical Testing of Steel Products |
| A931 | Tension Testing of Wire Rope and Strand |
| B565 | Shear Testing of Aluminum & Aluminum-Alloy Rivets |
| B769 | Shear Testing of Aluminum Alloys |
| B794 | Durability Wear Testing of Separable Electrical Connector Systems |
| C273 | Shear Properties of Sandwich Core Materials |
| C297 | Flatwise Tensile Strength of Sandwich Constructions |
| C393 C373 C773 |
Flexural Properties of Sandwich Constructions Water Absorption, Bulk Density, Apparent Porosity, and Apparent Sp. Gravity of Fired Whiteware Products Compressive Strength of Fired Whiteware |
| D198 | Static Tests of Lumber in Structural Sizes |
| D412 | Vulcanized Rubber & Thermoplastic Elastomers - Tension |
| D543 | Evaluating the Resistance of Plastics to Chemical Reagents |
| D570 | Water Absorption of Plastics |
| D575 | Rubber Properties in Compression |
| D624 | Tear Strength of Vulcanized Rubber and Thermoplastic Elastomers |
| D638 | Tensile Properties of Plastics |
| D648 | Deflection Temperature of Plastics under Flexural Load |
| D695 | Compressive Properties of Rigid Plastics |
| D696 | Coefficient of Linear Thermal Expansion of Plastics |
| D732 D737 |
Shear Strength of Plastics by Punch Tool Air Permeability of Textile Fabrics |
| D747 | Apparent Bending Modulus of Plastics by Means of a Cantilever Beam |
| D774 | Bursting Strength of Paper |
| D790 | Flexural Properties of Plastics and Insulating Materials |
| D792 | Density and Specific Gravity of Plastics |
| D882 | Tensile Properties of Thin Plastic Sheeting |
| D885 | Test Methods for Tire Cords and Industrial Filament Yarns |
| D897 | Tensile Properties of Adhesive Bonds |
| D903 | Peel or Stripping Strength of Adhesive Bonds |
| D905 | Strength of Adhesive Bonds in Shear by Compression |
| D952 | Bond Strength of Sheet Plastics and Electrical Insulating Materials |
| D1002 | Shear Strength of Single Lap Adhesive Bonds |
| D1004 D1037 |
Initial Tear Resistance of Plastic Films Properties of Wood- Based fiber and Particle Panel Materials |
| D1042 | Linear Dimensional Changes Under Accelerated Aging Conditions |
| D1043 | Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test |
| D1204 | Linear Dimensional Changes of Non-rigid Thermoplastic Film at Elevated Temp |
| D1424 | Tear Resistance of Fabrics (Elmendorf Method) |
| D1621 | Compressive Properties of Rigid Cellular Plastics |
| D1622 | Apparent Density of Rigid Cellular Plastics |
| D1623 | Tensile and Adhesion properties of Rigid Cellular Plastics |
| D1708 D1761 |
Tensile Properties of Plastics by Microtensile Specimens Mechanical Fasteners in Wood |
| D1876 | Peel Resistance of Adhesives |
| D1938 D2095 |
Tear-Propagation Resistance (Trouser Tear) of Plastic Film Tensile Strength of Adhesives by Bar and Rod Specimens |
| D2164 | Testing Structural Insulating Roof Deck |
| D2256 | Tensile Properties of Yarns |
| D2343 | Tensile Properties of Glass Fiber Strands, Yarns, and Rovings |
| D2344 | Short-Beam Strength of Polymer Matrix Composite Materials |
| D2412 | External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| D2718 | Structural Panels in Planar Shear |
| D2737 | Polyethylene (PE) Plastic Tubing |
| D2979 | Pressure-Sensitive Tack of Adhesives Using an Inverted Probe Machine1 |
| D2990 | Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
| D3039 | Tensile Properties of Polymer Matrix Composite |
| D3163 D3165 |
Strength of Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading Strength Properties of Adhesives in Shear by Tension - Single Lap - Shear Assemblies |
| D3330 | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape |
| D3574 | Test Methods for Flexible Cellular Materials |
| D3580 | Vibration (Vertical Linear Motion) Test of Products |
| D3611 | Accelerated Aging of Pressure Sensitive Tapes |
| D3983 D4475 |
Strength and Shear Modulus of Adhesives by Tensile-Lap Specimen Shear Strength of Pultruded Reinforced Plastic Rods by the Short - Beam Method |
| D5034 | Breaking Strength and Elongation of Textile Fabrics |
| D5035 | Breaking Force and Elongation of Textile Fabrics (Strip Method) |
| D5151 | Detection of Holes in Medical Gloves |
| D5278 | Elongation of Narrow Elastic Fabrics |
| D5934 | Modulus of Elasticity for Plastic Specimens by Three-Point Bending |
| D6653 | Standard Test Methods for Determining the Effects of High Altitude on Packaging Systems by Vacuum Method |
| E8 | Tension Testing of Metallic Materials |
| E72 | Strength Testing of Building Panels |
| E345 | Tension Testing of Metallic Foil |
| E1876 | Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio by Impulse Excitation of Vibration |
| F477 | Elastomeric Seals (Gaskets) for Joining Plastic Pipe |
| F623 | Performance Specs for Foley Catheters |
| F904 | Bond Strength or Ply Adhesion of Similar Laminates Made from Flexible Materials |
| F1306 | Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates |
| F1464 | Oxygen Concentrators for Domiciliary Use |
| F1691 | Determining Axial Pullout Strength of Medical Bone Screws |
| F2372 | Consumer Safety Performance Specification for Shopping Carts |
| EN 45502 | Active Implantable Medical Devices |
| EIA Standards | |
RS-186 |
|
| ETS Standards | |
| 300-019 | Environmental Tests for Telecommunications Equipment |
| IEC Standards | |
| 60068-1 | Environmental Testing Part I: General guidance |
| 60601-1 | Medical Electrical Equipment – Part 1: General requirements for basic safety and essential performance |
| 37 | Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties |
| 594-1 | Conical fittings with a 6 % (Luer) taper for syringes, needles and certain other medical equipment |
| 594-2 | Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment -- Part 2: Lock fittings |
| 5841-3 | Implants for surgery – Cardiac Pacemakers – Part 3: Low profile connectors (IS-1) for implantable pacemakers |
| 7864 | Sterile hypodermic needles for single use |
| 7886-1 | Sterile Hypodermic Syringes. Part 1: Syringes for manual use |
| 8359 | Oxygen Concentrators for Medical Use – Safety Requirements |
| 8536-4 | Infusion equipment for medical use – Part 4: Infusion sets for single use, gravity feed |
| 8569 | Measurement and evaluation of shock and vibration effects on sensitive equipment in buildings |
| 9022-10 | Optics and optical instruments -- Environmental test methods -- Part 10: Combined sinusoidal vibration and dry heat or cold |
| 9626 | Stainless steel needle tubing for manufacture of medical devices |
| 10282 | Single Use Sterile Rubber Gloves |
| 10555-1 | Sterile, single-use intravascular catheters – general requirements |
| 10555-3 | Sterile, single-use intravascular catheters – Central venous catheters |
| 10555-5 10846-1 |
Sterile, single-use intravascular catheters – Over-needle peripheral catheters Measurement of vibro-acoustic transfer properties of resilient elements |
| 11070 | Sterile Single-use Intravascular Catheter Introducers |
| JIS Standards | |
C0040 |
|
| C0041 | Environmental Tests – Shock and Vibration |
| MIL Standards | |
| 202 | Electronic and Electrical Component Parts |
| 810F | Test Method Standard for Environmental Engineering Considerations and Laboratory Tests |
| HDBK-17 | Composite Materials |
| P-26514 | Polyurethane Foam, Rigid or Flexible, for Packaging |
| J1455 | Environmental Practices for Electronic Equipment Design |
| JESD22-A104-B | Temperature Cycling for Electronic Circuits |
| JESD22-A102-C JESD22-B-103-B JESD22-B-104-C JESD22-A-106-B |
Accelerated Moisture Resistance for Electronic Circuits Vibration of Electronic Circuits Mechanical Shock for Electronic Circuits Thermal Shock for Electronic Circuits |
For more information on industry standards and compliance requirements for material testing, please contact us today.
