| ANSI Standards |
| ICWM-2004 |
Performance Standard for Casters & Wheels
|
| |
|
AAMI Standards
|
| |
|
| ID 26 |
Infusion Pump Performance Testing
|
| |
|
| ASTM Standards |
| |
|
| A370 |
Mechanical Testing of Steel Products |
| A931 |
Tension Testing of Wire Rope and Strand |
| B565 |
Shear Testing of Aluminum & Aluminum-Alloy Rivets |
| B769 |
Shear Testing of Aluminum Alloys
|
| B794 |
Durability Wear Testing of Separable Electrical Connector Systems |
| C273 |
Shear Properties of Sandwich Core Materials |
| C297 |
Flatwise Tensile Strength of Sandwich Constructions |
| C373 |
Water Absorption, Bulk Density, Apparent Porosity and Apparent Sp. Gravity of Fired Whiteware Products |
| C393 |
Flexural Properties of Sandwich Constructions |
| C773 |
Compressive Strength of Fired Whiteware Materials |
| C1161 |
Flexural Strength of Advanced Ceramics |
| D198 |
Static Tests of Lumber in Structural Sizes |
| D412 |
Vulcanized Rubber & Thermoplastic Elastomers - Tension
|
| D543 |
Evaluating the Resistance of Plastics to Chemical Reagents |
| D570 |
Water Absorption of Plastics |
| D575 |
Rubber Properties in Compression |
| D624 |
Tear Strength of Vulcanized Rubber and Thermoplastic Elastomers |
| D638 |
Tensile Properties of Plastics |
| D642 |
Standard Test Method for Determination of Compressive Resistance |
| D648 |
Deflection Temperature of Plastics under Flexural Load |
| D695 |
Compressive Properties of Rigid Plastics |
| D696 |
Coefficient of Linear Thermal Expansion of Plastics |
| D732 |
Shear Strength of Plastics by Punch Tool |
| D737 |
Air Permeability of Textile Fabrics |
| D747 |
Apparent Bending Modulus of Plastics by Means of a Cantilever Beam |
| D774 |
Bursting Strength of Paper |
| D790 |
Flexural Properties of Plastics and Insulating Materials |
| D792 |
Density and Specific Gravity of Plastics |
| D882 |
Tensile Properties of Thin Plastic Sheeting |
| D885 |
Test Methods for Tire Cords and Industrial Filament Yarns
|
| D897 |
Tensile Properties of Adhesive Bonds |
| D903 |
Peel or Stripping Strength of Adhesive Bonds |
| D905 |
Strength of Adhesive Bonds in Shear by Compression |
| D952 |
Bond Strength of Sheet Plastics and Electrical Insulating Materials |
| D999 |
Standard Method for Vibration Testing of Shipping Containers |
| D1002 |
Shear Strength of Single Lap Adhesive Bonds |
| D1004 |
Initial Tear Resistance of Plastic Films |
| D1037 |
Properties of Wood-Based Fiber and Particle Panels |
| D1042 |
Linear Dimensional Changes Under Accelerated Aging Conditions |
| D1043 |
Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test |
| D1204 |
Linear Dimensional Changes of Non-rigid Thermoplastic Film at Elevated Temp |
| D1424 |
Tear Resistance of Fabrics (Elmendorf Method) |
| D1621 |
Compressive Properties of Rigid Cellular Plastics
|
| D1622 |
Apparent Density of Rigid Cellular Plastics |
| D1623 |
Tensile and Adhesion properties of Rigid Cellular Plastics
|
| D1708 |
Tensile Properties of Plastics by Microtensile Specimens |
| D1761 |
Mechanical Fasteners in Wood |
| D1876 |
Peel Resistance of Adhesives |
| D1894 |
Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting |
| D1938 |
Tear-Propagation Resistance (Trouser Tear) of Plastic Film |
| D2095 |
Tensile Strength of Adhesives by Bar and Rod Specimens
|
| D2164 |
Testing Structural Insulating Roof Deck |
| D2256 |
Tensile Properties of Yarns |
| D2343 |
Tensile Properties of Glass Fiber Strands, Yarns, and Rovings |
| D2344 |
Short-Beam Strength of Polymer Matrix Composite Materials |
| D2412 |
External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| D2718 |
Structural Panels in Planar Shear |
| D2737 |
Polyethylene (PE) Plastic Tubing |
| D2979 |
Pressure-Sensitive Tack of Adhesives Using an Inverted Probe Machine1 |
| D2990 |
Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
| D3039 |
Tensile Properties of Polymer Matrix Composite |
| D3078 |
Standard Test Method for Determination of Leaks in Flexible Packaging by Bubble Emission
|
| D3079 |
Standard Test Method for Water Vapor Transmission of Flexible Heat-Sealed Packages for Dry Products
|
| D3163 |
Strength of Bonded Rigid Plastic Lap-Shear Joints in Shear by Tension Loading |
| D3165 |
Strength Properties of Adhesives in Shear by Tension – Single Lap-Shear Assemblies
|
| D3330 |
Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape
|
| D3332 |
Mechanical-Shock Fragility of Products, Using Shock Machines |
| D3574 |
Test Methods for Flexible Cellular Materials |
| D3580 |
Vibration (Vertical Linear Motion) Test of Products |
| D3611 |
Accelerated Aging of Pressure Sensitive Tapes
|
| D3983 |
Strength and Shear Modulus of Adhesives by Tensile-Lap Specimen |
| D4169 |
Standard Practice for Performance Testing of Shipping Containers and Systems |
| D4332 |
Standard Practice for Conditioning Containers, Packages, or Packaging Components for Testing
|
| D4475 |
Shear Strength of Pultruded Reinforced Plastic Rods by the Short-Beam Method |
| D4728 |
Standard Test Method for Random Vibration Testing of Shipping Containers |
| D4991 |
Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method
|
| D5034 |
Breaking Strength and Elongation of Textile Fabrics |
| D5035 |
Breaking Force and Elongation of Textile Fabrics (Strip Method)
|
| D5151 |
Detection of Holes in Medical Gloves |
| D5276 |
Standard Test Method for Drop Test for Loaded Containers by Free Fall
|
| D5278 |
Elongation of Narrow Elastic Fabrics
|
| D5487 |
Standard Test Method for Simulated Drop of Loaded Containers by Shock Machines
|
| D5934 |
Modulus of Elasticity for Plastic Specimens by Three-Point Bending |
| D6653 |
Standard Test Methods for Determining the Effects of High Altitude on Packaging Systems by Vacuum Method |
| D7234 |
Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| E8 |
Tension Testing of Metallic Materials |
| E72 |
Strength Testing of Building Panels
|
| E345 |
Tension Testing of Metallic Foil |
| E1876 |
Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio by Impulse Excitation of Vibration
|
| F88 |
Standard Test Method for Seal Strength of Flexible Barrier Materials |
| F477 |
Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
| F623 |
Performance Specs for Foley Catheters
|
| F904 |
Bond Strength or Ply Adhesion of Similar Laminates Made from Flexible Materials
|
| F1140 |
Standard Test Methods for Internal Pressurization Failure Resistance of Unrestrained Packages for Medical Applications |
| F1306 |
Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates |
| F1464 |
Oxygen Concentrators for Domiciliary Use
|
| F1608 |
Standard Test Method for Microbial Ranking of Porous Packaging Materials (Exposure Chamber Method)
|
| F1691 |
Determining Axial Pullout Strength of Medical Bone Screws
|
| F 1929 |
Standard Test Method for Detecting Seal Leaks in Porous Medical Packaging by Dye Penetration
|
| F1980 |
Standard Guide for Accelerated Aging of Sterile Medical Device Packaging
|
| F2096 |
Standard Test Method for Detecting Gross Leaks in Medical Packaging by Internal Pressurization (Bubble Test)
|
| F2372 |
Consumer Safety Performance Specification for Shopping Carts |
| |
|
|
CENELEC Standards
|
| |
|
| EN 45502 |
Active Implantable Medical Devices |
| |
|
| EIA Standards |
| |
|
|
RS-186
|
|
| |
|
| ETS Standards |
| |
|
| 300-019 |
Environmental Tests for Telecommunications Equipment |
| |
|
| IEC Standards |
| |
|
| 60068-1 |
Environmental Testing Part I: General guidance |
| 60068-2-14 |
Basic Environmental Testing Procedures Test N: Change of temperature |
| 60068-2-33 |
Environmental Testing- Guidance on change of temperature tests |
| 60068-2-38 |
Composite Temperature/Humidity Cyclic Test |
| 60068-2-64 |
Vibration, broad-band random (digital control) and guidance |
| 60601-1 |
Medical Electrical Equipment – Part 1: General requirements for basic safety and essential performance
|
| |
|
|
ISO Standards
|
| |
|
| 37 |
Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties
|
| 594-1 |
Conical fittings with a 6 % (Luer) taper for syringes, needles and certain other medical equipment
|
| 594-2 |
Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment -- Part 2: Lock fittings |
| 595 |
Reusable all-glass or metal-and-glass syringes for medical use -- Part 1: Dimensions |
| 2247 |
Packaging -- Complete, filled transport packages and unit loads -- Vibration tests at fixed low frequency |
| 5841-3 |
Implants for surgery – Cardiac Pacemakers – Part 3: Low profile connectors (IS-1) for implantable pacemakers
|
| 7864 |
Sterile hypodermic needles for single use |
| 7886-1 |
Sterile Hypodermic Syringes. Part 1: Syringes for manual use |
| 8318 |
Packaging -- Complete, filled transport packages and unit loads -- Sinusoidal vibration tests using a variable frequency
|
| 8359 |
Oxygen Concentrators for Medical Use – Safety Requirements |
| 8536-4 |
Infusion equipment for medical use – Part 4: Infusion sets for single use, gravity feed |
| 8569 |
Measurement and evaluation of shock and vibration effects on sensitive equipment in buildings
|
| 8537 |
Sterle single-use syringes, with or without needle for insulin
|
| 9022-10 |
Optics and optical instruments -- Environmental test methods -- Part 10: Combined sinusoidal vibration and dry heat or cold |
| 9022-15 |
Environmental test methods -- Part 15: Combined digitally controlled broad-band random vibration and dry heat or cold
|
| 9022-19 |
Environmental test methods -- Part 19: Temperature cycles combined with sinusoidal or random vibration |
| 9626 |
Stainless steel needle tubing for manufacture of medical devices |
| 10282 |
Single Use Sterile Rubber Gloves |
| 10555-1 |
Sterile, single-use intravascular catheters – general requirements |
| 10555-3 |
Sterile, single-use intravascular catheters – Central venous catheters |
| 10555-5 |
Sterile, single-use intravascular catheters – Over-needle peripheral catheters |
| 10846-1 |
Measurement of vibro-acoustic transfer properties of resilient elements |
| 11070 |
Sterile Single-use Intravascular Catheter Introducers |
| |
|
|
ISTA Standards
|
| |
|
| ISTA |
Pre-Shipment Test Procedure |
| |
|
| JIS Standards |
| |
|
|
C0040
|
|
| C0041 |
Environmental Tests – Shock and Vibration |
| |
|
| MIL Standards |
| |
|
| 167 |
Vibration Testing |
| 202 |
Electronic and Electrical Component Parts |
| 810F |
Test Method Standard for Environmental Engineering Considerations and Laboratory Tests |
| 883 |
|
| HDBK-17 |
Composite Materials |
| P-26514 |
Polyurethane Foam, Rigid or Flexible, for Packaging |
| |
|
|
NAVMAT Standards
|
| |
|
| P-9492 |
Temperature Cycling and Random Vibration |
| |
|
| NEMA |
| LD-3-2000 |
High Pressure Laminates |
| |
| PDA Technical Reports |
| Tech. Report #27 |
Pharmaceutical Package Integrity, 1998 Supplement, Vol. 52 , No: 52 |
| Tech. Report #39 |
Cold Chain Guidance for Medicinal Products: Maintaining the Quality of Temperature-Sensitive Medicinal Products Through The Transportation Environment, Sept/Oct 2005, Supplement, Vol. 59, No: S-3 |
| |
|
SAE Standards
|
| J1455 |
Environmental Practices for Electronic Equipment Design |
| |
|
|
JEDEC Standards
|
| |
|
| JESD22-A104-B |
Temperature Cycling for Electronic Circuits |
| JESD22- A102-C |
Accelerated Moisture Resistance for Electronic Circuits |
| JESD22- B103-B |
Vibration for Electronic Circuits |
| JESD22-B104-C |
Mechanical Shock for Electronic Circuits |
| JESD22- A106-B |
Thermal Shock for Electronic Circuits |
| |
|
|
TAPPI Standards
|
